Oooh! That’s so pretty…

RSS
Oooh! That’s so pretty…

Alcohol inks can provide a variety of different designs. In this entry, we are going to talk about the marble or galaxy look. This was one of my first and favorite cups to do! I originally tried to use my own inks by dabbing them on, but they weren’t very vibrant. That’s when I switched to the Tim Holtz inks and applied by dropping the ink into the epoxy. Here is how to do it:

  1. Set-Up- Find the correct sized noodle or football and insert it inside your cup with the PVC pipe sticking out so that you can hold the PVC without touching the cup. Some people prefer to tape off areas like the top rim or bottom rim. Use electrical tape if you choose to do so. I, however, like a full covered cup.
  2. Prime your cup- When glittering a cup, it is best to use a base color. It can match the glitter to help give full coverage or you can use a different color to create a cool effect. I would say I use a white base more than anything. It gives the glitter a brighter look! I use the Rustoleum 2 in 1 primer. It doesn’t have to be a perfect coat because the glitter will hide blemishes.
  3. Dry- Let the paint dry completely before moving on.
  4. Mix Epoxy-
    1. Put on gloves
    2. Pour each part A and part B in equal amounts into their own measuring cup. I use FIFO bottles to hold my epoxy and allow me to easily pour it into the measuring cups.
    3. Use a heat gun to very lightly heat part A to help pull out any bubbles
    4. Pour part B into a dixie cup. Be sure to scrape the edges and get everything you can out of the measuring cup using a popsicle stick.
    5. Pour part A into the dixie cup and scrape the edges.
    6. Slowly stir your epoxy continuously. Scrape the sides every so often. Don’t scrape too hard on a dixie cup or the wax will get in your epoxy and cause lumps!
    7. The epoxy is completely stirred when you can see clearly the bottom of your popsicle stick.
    8. THIS IS DIFFERENT! I always had a couple drops of white acrylic paint to my epoxy. This helps create a solid color and less transparent. It also helps the ink to show up more vibrant.
    9. Stir well.
    10. I let my epoxy sit for about 2 minutes to help release any bubbles
    11. I learned the hard way not to use a heat gun at this point. It will melt the wax on the dixie cup.
  5. Apply Epoxy- This is a step you will have to play with until you find what works for you. With your cup on the turner rotating, pour small amounts of epoxy onto your cup and use your index finger to spread it evenly around the cup. Once there is epoxy on the entire cup, then start the process if making it even. I start at the lip of the cup and swipe my finger straight down towards the bottom of the cup and around the bottom edge. Do this all the way around. Then start at the bottom edge and swipe your finger straight up to the top and around the inside of the lip. This helps for a better seal and you will use your straightedge to clean up the top when everything is done.

6. Drop ink- Now is when you will drop your ink onto your cup. Use as much or as little, there is no right way. I suggest using 3-4 colors. And remember when they touch they will mix and create a new color!

7. Apply Heat- This is the step that will allow the inks to mix and swirl. Apply the heat all over using quick, brisk swipes up and down. You may find you need to add more ink or concentrate on certain areas to mix more.

8. Dry- Epoxy likes to dry around 75 degrees for 4-5 hours. I like to let mine dry closer to 6-8 hours.

9. Epoxy- When using inks on cups, it usually takes 2 coats before it’s strong enough to sand. Repeat steps 7 and 8 until there is enough coverage to not damage the ink when you sand.

10. Sand- Lightly sand your cup until there is a smooth finish, with no bumps or rough spots.

11. Alcohol- Pour alcohol onto a paper towel and wipe down the cup, removing any debris left from sanding.

12. Apply design- After the alcohol is dry and the cup is clean, apply your design.

    Vinyl- Apply vinyl as normal. Make sure it is sealed against the cup so that epoxy cannot get under and create bubbles

    Printable vinyl- use the print and cut method on your vinyl cutter so that there is no excess white space. Apply without a carrier sheet. Carrier sheets will pull off the print. Do not use alcohol after vinyl is applied. It will smear the ink.

    Waterslide-

    1. White- you should have used the print and cut feature to remove excess white.
    2. Clear- print and cut closely around the edge.

    Spray your waterslide with a clear sealer, like clear matte spray paint, to prevent the ink from smearing when it is placed in water. Use several coats. Let it dry completely between each coat. When dry, place the decal in a bowl of water and separate from carrier sheet. Wet the tumbler so that the decal can be moved. Apply to tumbler. Use a sponge brush to softly run across the decal and help remove air bubbles and excess water. Dab with a paper towel. Let it dry and then seal cup with the clear spray again.

    1. Epoxy- Epoxy more layers as needed, sanding and wiping with alcohol in between. I have found that using acetone to wipe before the last coat helps in making the surface perfect.
    2. Clean- After your cup is dry, use a straight edge or Exacto knife to cut across the top edge. Angle the blade inward so that you don’t break the seal on the outside. This should give you a clean smooth edge. Then pop away the epoxy rim on the inside of the cup. Use acetone (NOT ALCOHOL) to remove any excess paint, adhesive or glitter that is left inside the cup. When done your cup rim should be smooth with no residue and the inside should be spotless!
    3. Harden- It will take the cup 24-72 hours to fully harden. I suggest leaving it on the drying rack during this time. I have set on tables and sometimes it will pull up dirt or get stuck to the table. If you try to clean it up after it hardens, it will be more difficult.
    4. Finish- If selling or giving your cup away, we suggest placing a tumbler care card inside. You can find one to print and cut on Etsy here: Care Card

    Use the blank box from The Steel Magnolia Company to package your product. Add your own label using printable vinyl, if desired. If shipping, put back inside the bubble wrap and box it. The best way to ship is using a flat rate bubble mailer from USPS.

    Next, we'll talk about using alcohol inks to design a woodgrain look!

    Previous Post Next Post

    • Nikki Hamilton
    Comments 0
    Leave a comment
    Your Name:*
    Email Address:*
    Message: *

    Please note: comments must be approved before they are published.

    * Required Fields